10-Reasons-Why-People-Hate-Patio-Door-Lock-Repair-Patio-Door-Lock-Repair-f

Patio Door Lock Repairs

Over time, patio doors undergo wear and tear that can lead to locks that fail. There are fortunately, a number of easy and efficient ways to restore your uPVC patio door's security.

It's about realigning the lock or cleaning the mechanism that locks, these quick fixes can help you make your home more secure.

Clean the Lock

Patio doors are ideal to let the outdoors in and keeping the elements out. However, they can be risky for security if the lock doesn't work properly. Over time, wear and tear, cold and hot weather dirt, and other debris can cause your patio door lock to become difficult to operate. With a little maintenance, you can ensure your patio door's locks always function properly.





To begin with, it's important to clean the lock on your patio door and all of its moving parts. This will help get rid of any grime and coatings that may hinder the lock from functioning in the way it should. Begin by wiping down the moving parts of your patio door's lock with a damp, clean cloth. then use a scouring pad or rough damp cloth to scrub any hard-to-reach areas of the door and frame that are covered in dirt. It is recommended to wipe the entire lock with dry cloth to get rid of any remaining dampness and let it to air dry prior to using it again.

If you have an outdoor door that has a pin tumbler latch mechanism You can apply lubrication to the lock by applying powdered graphite to the key or applying an lubricant based on Teflon like WD-40 Multi-Use. This type of lubricant can be easy to apply and doesn't break down with time. If you are unable to find the right lubricant to use with your lock, apply a pencil that has a more of a thicker tip. Place the pencil in the lock and jiggle it around a bit to distribute the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio doors clear from dirt, dust and debris. These tracks are particularly vulnerable to ice, snow, and other particles, which can cause them block or become stuck. This can make it difficult for your patio door to open and shut.

Clean Repair My Windows And Doors and rollers of sliding patio doors by removing weather stripping that is damaged or dirty. Clean it, then replace it. The same is true for rollers on patio doors, which can be cleaned and sprayed with non-stick lubricant that will allow them to move freely.

Lubricate the moving parts

uPVC French doors, like sliding patios, operate by using 3 to 4 or sometimes, 5 points locking mechanisms. This includes the lock cylinder and handle which is operated by keys. These doors require maintenance, lubrication of the moving parts. This can be done using an oil that is thin but not WD40. This should be done at least once a year.

If hinges that are sagging don't cause the issue, it could be that the door isn't aligned. It could be rubbing against or catching the strike plate's opening in the frame. The solution is to take off the strike plate, and then use an abrasive chisel to increase the size of the mortise that it rests in. This will permit the latch to fit into the hole, and prevent it from hitting the frame.

Find the width of the cylinder with a piece of wood or a book that is able to fit into the space above the adjustment screw. The outer dimension is measured from the outside of door to the center of cylinder. The inner dimension is measured from the center adjustment screw until the end cylinder.

Verify the width of the lock.

If your patio door latch is difficult to turn even after cleaning and lubricating, there's a possibility that it is out of alignment with the strike plate hole. Verify that the door is properly balanced and if the hinge screws are secure However, in many cases, moving the strike plate up or down can fix the issue.

Most of the time, the issue occurs when the strike of the lock is too small for the latch to properly engage. In this case you'll need to expand the hole with the hammer or chisel and then test the latch to make sure that it connects to the strike plate in a smooth manner without rubbing against or catching on the door's frame jamb.

Before buying a replacement lock, you should first identify the type of mortise lock you have. You can do this by looking at the faceplate of the lock and determining whether it is square or round. Look at each screw hole on the current lock and note the size. This will help you find an alternative lock that is of the same size and fits perfectly into the hole that you already have.

In addition to identifying the current mortise lock, you'll also need to check it for any bends or scratches that may need repairing. A badly bent or damaged latch is more likely than one that's frequently used to break. Replace the lock if it displays signs of damage.

After you've examined the lock and identified which kind of replacement you require now is the time to start working on the actual repair. Remove the old handle and spindle out of your patio door, and then insert the new one. Start by putting in the handle in the interior by aligning it with the spindle, and then securing it with the two bolts or screws that hold it. Install the exterior handle after the interior handle. After you've completed these steps check the handles to make sure they are able to open and close easily and that the latch works correctly with the strikeplate.

Make sure you check the Strike of the door.

The strike plate and the door latch are two pieces that work together to lock the door. An incorrectly aligned strike plate and door latches can cause the latch to not latch the door in a proper manner. This issue is usually simple to solve.

First, check the holes in the strike plate's receiving to ensure they are free of obstructions, such as dirt or plastic plugs. Then loosen the screws that secure the strike plate in place and allow it to move vertically, but not removing it from the frame of your door. Adjust the strike plate to align its holes for receiving with the latch hooks of the door latch. Once the strike plate has been adjusted tighten all screws and test whether the door closes smoothly.

Door strike plates can be difficult to access for homeowners with sliding patio doors, but they're essential for locking and unlocking your door. These metal plates are usually located at the top and bottom of the door jamb, which is where they are used to support the door's latch. The door latch slides onto the strike plate and forms an airtight seal. If the strike plate is damaged, rusted, or not properly installed, it could hinder the latch from locking the door securely.

One common reason for an outdoor door lock to stick or not close is a misalignment of the latch and strike plate. This can be checked with the "lipstick" test. Apply some lipstick on the outside of the deadbolt, then cover it with masking tape. When you close the door the lipstick will leave a mark on the tape, showing you exactly where the latch connects to the strike plate. If the mark is too low or high you can easily alter the strike plate.

If your patio door locks for sliding aren't functioning properly, they can keep your home secure from intruders. It is imperative to resolve this issue as quickly as possible. By following these easy steps, you can fix your patio door's lock and restore its functionality in a matter of minutes.