10-Quick-Tips-On-Patio-Door-Lock-Repair-n

Patio Door Lock Repairs

Over time, patio doors experience wear and tear that can result in locks that fail. Fortunately, there are several simple and efficient ways to restore your uPVC patio door's security.

It's about realigning the lock or cleaning the locking mechanism These simple fixes can increase the security of your home.

Clean the Lock

While patio doors are a great way to let the outside in and keep out the elements, they can also be security risks in the event that your lock isn't operating as it should. Over time, wear and tear, hot and cold weather dirt and debris can affect your patio door's lock and cause it to become difficult to open. With a little care, you can make sure that the lock on your patio door always works properly.

To begin with, it's essential to clean your patio door's lock and all its moving parts. This will help remove any coatings or dirt that might be hindering your lock from working correctly. Start by wiping down all the moving parts of the lock for your patio door with a damp cloth, then employ a scouring pad or rough damp cloth to scrub any difficult-to-access areas of the door or frame that are ingrained with dirt. It is recommended to wipe the entire lock with dry cloths to eliminate any remaining dampness, and allow it to air dry before using it again.

If you have an exterior door that is fitted with pin tumbler latch mechanisms it is possible to lubricate the lock by applying graphite powdered to the key or applying a lubricant made of Teflon, such as WD-40 Multi-Use Product. This type of lubricant is able to be applied with ease and does not dissolve over time. If you are unable to find the right lubricant for your lock, apply a pencil that has a larger tip. Put the pencil in the lock, then shake it around to distribute the graphite.

Regular maintenance is also required to keep the tracks of sliding patio doors free from dirt, dust and other debris. These tracks can be especially susceptible to snow and ice, which can cause them become stuck or slack, making it harder for your patio doors to open and close.

Tracks for sliding patio doors and rollers can be cleaned by removing dirty or damaged weather stripping and then cleaning it, before replacing it. The rollers of patio doors can be cleaned and sprayed with an oil that is non-stick.

Lubricate the moving parts





uPVC french doors, which are similar to sliding patio doors, operate by using 3-4 or sometimes five-point locking mechanisms, which include the lock cylinder and handle controlled by the key. These doors require maintenance, oiling of the moving parts. This can be accomplished with a thin oil however, never WD40. It is recommended to do it at least once a year.

If sagging hinges aren't the reason, the door could be skewed and catch or striking the strike plate's hole in the frame. The solution is to take off the strike plate and then use an abrasive chisel, which will enlarge the mortise that it rests in. This allows the latch to fit properly in the hole, and also prevents rubbing or catching on the frame.

Once the cylinder is cleared of the way take a measurement of its width using an object or a piece of wood that can fit into the gap of adjustment screw above the lock. The outer dimension is measured from the outside of the door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the lock's length

If your patio door latch isn't able to turn, even after cleaning and lubricating, it's possible that it is out of alignment with the strike plate hole. Verify that the door is in a balanced position, and that the hinge screws are in good condition. In most cases, however, simply moving the strike plate upwards or downwards can fix the problem.

patio door repair is when the strike of the lock is too small for the latch to engage. In patio door repair 'll have to increase the hole using the hammer or chisel and then test the latch to make sure that it contacts the strike plate without rubbing against or catching on the door's frame jamb.

Before purchasing a new lock, you should first determine the mortise type of lock you currently have. You can do this by looking at the faceplate of the lock and noting if it is round or square. Look at each screw hole on the existing lock and note their dimensions. This will help you to find a replacement lock that is exactly the same width and fits into the hole you have already.

You'll need to locate the mortise lock, and then examine it for any bends, scratches or other damage that needs to be repaired. A damaged or bent latch is more likely than one that has frequently used to break. Replace the lock if it shows indications of damage.

Once you've inspected the lock and determined which type of replacement you'll need, it's time to start working on the actual repair. Remove the old handle and spindle from your patio door, and then insert the new one. Begin by installing the handle in the interior by aligning it with the spindle, and then securing it in place by using the two screws or bolts that secure it. Once the handle's interior is installed, put in the exterior handle and screw it in the position as well. After you've completed the steps then you can test the new handles to ensure they open and close easily and that the latch is catching properly with the strike plate.

Check the Strike of the Door.

The strike plate and the door latch are two pieces that work together in order to secure the door. If these are misaligned, the latch won't latch the door shut correctly. Fortunately, this issue is often easy to fix.

Check the holes for receiving of the strike plate to ensure they are clear of obstructions such as dirt or plastic plugs. Then loosen the keeper screws that hold the strike plate in place and allow it to move horizontally, but not separating it from the door frame. Then, you can adjust the strike plate so that its holes for receiving are aligned with the latch hooks on the door latch. After the strike plate has been adjusted, tighten the screws and test the door to determine if it shuts smoothly with the new adjustment.

These plates are difficult to reach for homeowners with sliding patio doors. However, they are essential to secure and unlock your door. These metal plates are usually located at the top and bottom of the door jamb, where they support the door's latch. The door latch is inserted into this strike plate and creates a seal. If the strike plate has been damaged or rusted, or if it is not properly installed the latch may not be able to lock the door properly.

The most common reason for a patio door lock to not close or not close is a misalignment of the latch and the strike plate. This can be verified using the "lipstick" test. Apply a little lipstick along the edge of the deadbolt, then cover it with masking tape. When you shut the door the lipstick will leave an impression on the tape, indicating you exactly where the latch connects to the strike plate. If the mark is too high or low it is possible to alter the strike plate.

If your patio door locks for sliding aren't functioning properly they can help keep your home safe from burglars. It is imperative to fix this problem as soon as possible. Follow these simple steps to repair your patio door lock and restore its functionality.