25-Surprising-Facts-About-Patio-Doors-Repair-x

Patio Doors Repair - How to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet

Patio doors can provide a convenient and comfortable transition between your home and outdoor space. By keeping the air inside your home, they could save you money on cooling or heating bills.

But over time, your sliding glass or French doors could lose their shine. Simple repairs can keep your sliding glass or French doors looking like new.

Weatherstripping

You're walking your dog to the park around 5 AM, and you end up into a puddle near your sliding patio door. You look around and realize that the rain from last night has blown through the patio door seals. Buckle up, this isn't going to be a five-minute project. But with a little patience and a few tools to fix the issue, you'll be able to do it and save your dog from wet, cold feet as well.

The key is to replace the weatherstripping, which seals the gap between your door and jamb, which prevents drafts, pests and moisture. It also helps keep your energy bills down. If you inspect your doors and windows you can determine whether the weatherstripping should be replaced or not.

There are a variety of weatherstripping that you can choose from such as open-cell and felt foam, thermoplastic rubber, and metals like bronze or copper. Each has its pros and drawbacks. Felt and open cell foam are cheap, but they tend to be ineffective and visible at blocking airflow. Vinyl is more expensive but it's durable and is resistant to moisture. Rubber is a great option for areas with high traffic because it will not wear out as fast.

To install new weatherstripping remove the patio door from the frame by loosening the screws that adjust the rollers using a screwdriver. Then, using a flathead screwdriver, remove the plugs that secure the weatherstripping on the bottom of the frame. Remove the weatherstripping that was previously installed from the frame, and then remove any adhesive residue. Then, cut the replacement to the correct length, peel back the plastic strip at one end and apply it to the jamb with the putty knife.

After that, you can reinstall the door and readjust the roller screws until the door is in the track and shuts correctly. Apply waterproof caulk wherever the stationary panel is positioned to block sliding doors and where the edge of the panel joins the frame. This is not as secure a seal than the weatherstripping, however, it will last for a time.

Handles and locks

Locks and handles for your patio door are essential to ensure the security of your home. As time passes, they could be damaged or worn out and require replacement. The spindle that connects the inside and exterior handles could also require replacement.

To replace a handle for a patio door first, remove the old one by unscrewing any screws that are holding it in place. After removing the handle, use a level and ensure that the door is straight. If the door isn't in a straight line, it could interfere with the lock. This could lead to problems in the future.

Close and open the handle several times after installation to ensure it is working properly. If you encounter any issues ask the manufacturer or a hardware expert for assistance. To avoid problems in the future, it is a good idea also to lubricate your lock mechanism with silicone-based lubricant.

The most common type of patio door lock is a mortise latch. It's usually made of steel and fits in a pocket cut into the door frame. These locks are commonly used on sliding wood and aluminum doors. When replacing a mortise lock it is important to measure a few things before purchasing a new lock. The measurements you need to take include the mounting hole locations and the location of the keyway inside the lock.

Certain patio door handles come with a built-in locking mechanism that's integrated into the handle. These handles have a rectangular key cylinder that fits inside the handle's keyway. If you have this kind of patio door both the inside and exterior locks are combined into one. This type of patio door is often found on aluminum sliding doors.

If your patio door latch does not stay locked the lock tongue might not be catching the hasp in the right way. Another possibility is that the sliding door is not completely parallel with the jamb's side. Try opening the door about an inch and spotting it against the frame to determine if there is any gap between the door and the jamb. If there is patio door repairs near me , reposition the rollers at the bottom left or right side of the patio to make it perfectly parallel to the jamb.





Misalignment

Over time the tracks and rollers will lose their proper alignment. This could cause doors to become stuck or difficult to move. This can also let drafts and cold air into your home, which can reduce the efficiency of your energy. Fortunately, misalignment is simple to fix and avoid. Applying a silicone-based grease the rollers and tracks will make your doors glide again. This is a good option for those who want to keep your doors operating at their best.

A damaged or ripped screen can be a problem. It could be an inconvenience or even a danger. It may also hinder the doors from opening and closing properly, leading to energy loss. In some cases, the torn screen can be replaced, however in other cases, it's best to replace the entire door. If you have a torn window screen, make sure you wash it thoroughly. Also, make sure you don't turn the handles of the door in the wrong way.

Hinges can become looser over time due to frequent usage or normal wear. This can be corrected by regularly tightening screws. It's a simple job you can do yourself. However, if you are not comfortable with the task, you should consult an expert.

It is also recommended to clean the rollers and tracks of your patio doors regularly. A simple brushing or vacuuming will get rid of dust and debris that could impede the smooth operation of your patio doors. You can use a special tool for stubborn dirt or rust. The inspection and tightening of the screws on the hinges may help with misalignment, but sometimes it's necessary to replace them altogether to ensure a solid and durable seal.

If your frames for your patio doors are sagging or warped, this can affect their alignment and performance. The warping or shifting may occur due to changes in the foundation of your home, but can be caused by poor installation or simply due to frequent use. A professional can replace or repair your patio door frame and ensure that it is properly aligned. This will allow it to function at its best.

Rollers

The sliding patio doors are a great way to bring the outdoors in and let in lots of light, but they need some care to ensure that they're moving smoothly. If you find yourself having to pull the handle hard to get the door to move or it isn't sliding as it did in the past, it could be the rollers. As time passes, the lower track may become clogged with dirt, sand, and mud that makes it hard for the rollers to move over. Clean it and spray it with a lubricant, such as 2Slick to see if it helps.

If the tracks have been cleaned, but the rollers aren't gliding freely, then it's time to replace them. Replacement rollers are available for your door and track type. You can find them at most hardware shops however, you will require someone to assist you in removing and reinstall the rollers. Before you order replacements, make sure to take an image of the roller assembly placed in the door frame so the experts can identify the exact model and the type you need. They can also look out for specific features like dimples or bumps, cutouts or flared edges to narrow down your replacement options.

Once the rollers are replaced, you'll need to reinstall your sliding door into its frame. Get help in this regard as the door is very heavy. Examine if there are any screws holding the track on either side of the frame. If there are you must ensure that they are loose enough to allow the bottom of door to slide into the channel that is above the frame. If there is a screen door, take it from the opening and ensure it's clear of the track and rollers.

After the new rollers are in then carefully insert the door into the frame and swing it back into position. If the new rollers are adjustable you can adjust them to give the door clearance where it needs it.