7-Simple-Changes-That-Will-Make-The-Difference-With-Your-Patio-Doors-Repair-m

Patio Doors Repair - How to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet

Patio doors can provide a convenient and comfortable transition between your indoor and outdoor space. By keeping air inside your home, they can save you money on heating or cooling bills.

Over time, the shine of your sliding glass or French door can fade. Simple repairs can keep your French or sliding glass doors looking and working like new.

Weatherstripping

It's 5 am and you're letting your dog out for his morning constitutional when you stumble into the puddle of water near the sliding patio doors. You turn around and see that the rain of last night has blown through the patio door seals. This isn't going to be an easy project. With a little patience and a few tools, you can fix it and prevent your dog's feet from getting cold and wet.

It is crucial to replace the weatherstripping which closes the gap between your door and jamb. This will prevent drafts, pests and moisture. It also helps keep your energy bills low. If you inspect your doors and windows, you can determine whether the weatherstripping should be replaced or not.

There are a variety of weatherstripping that are available, including felt, open-cell foam, vinyl, thermoplastic rubber and metals like bronze and copper. Each has its advantages and disadvantages. Felt and open cell foam are inexpensive, but they tend to be ineffective and visible when blocking airflow. Vinyl is more expensive, but it holds up well and resists moisture. Rubber is a good choice for areas with high traffic because it will not wear as fast.

To install new weatherstripping remove the patio door from the frame by loosening the screws that adjust the rollers using the help of a screwdriver. Then, with a flathead screwdriver, remove the plugs that hold weatherstripping at the bottom of the frame. Remove the old weatherstripping from the frame and clean any adhesive remnants. Then, cut the new to the appropriate length, then peel off the plastic strip at one end, and apply it using a putty blade to the jamb.

After you're done, put back the door and readjust the roller screws so that the door is positioned in the track and shuts properly. Apply caulk that is waterproof where the stationary panel is positioned to block sliding doors and at the point where the edge of the panel joins the frame. This is a less secure seal than weatherstripping, but it should be able to last for a period of time.

Handles and locks

Locks and handles for patio doors are important for the security of your home. Over time, they can become damaged or worn and require replacement. The spindle connecting the interior handles and the exterior handles may also be replaced.

To replace a handle on a patio door, remove the old one first, taking off any screws that hold it in place. After removing the handle, you can use a level and make sure that the door is straight. If the door is not straight it could cause problems with the lock and cause issues in the future.

Close and open the handle several times after installing it to make sure it's working correctly. If you have any problems ask the manufacturer or a specialist in hardware for assistance. To avoid problems in the future, it is a good idea to also lubricate your lock mechanism using lubricant made of silicone.

The most commonly used door lock for patio doors is the mortise latch. It's typically constructed of steel and is placed inside a pocket carved into the door frame. These kinds of locks are used on aluminum and wood sliding doors. Before purchasing a replacement mortise lock it is important to measure. The measurements you require include the locations of the mounting holes as well as the location of the keyway within the lock.

RepairMyWindowsAndDoors have a built-in locking mechanism that's integrated into the handle. The handles are rectangular key cylinder that fits in the handle's keyway. If you have this kind of patio door, the inside and outside locks are combined into one unit. This type of patio door is most commonly found on aluminum sliding doors.

If the latch on your patio door does not stay locked it could be because the lock tongue may not be catching the hasp correctly. Another possibility is that the sliding door isn't fully parallel to the jamb's side. Try opening the door for about 1 inch and then spotting it against the frame to determine whether there is any gap between the door and the jamb. If there is, adjust the rollers on the bottom left or right of the patio door to get it to be perfectly parallel to the jamb.

Misalignment

As time passes the door's tracks and rollers may lose their proper alignment. This could cause the door to become stuck or become difficult to move. It can also allow drafts and cold air enter your home, which can reduce energy efficiency. It is possible to correct the misalignment and prevented. Applying a silicone-based oil to the tracks and rollers can make your doors glide again. This is a good option for those who want to keep your doors operating at their top performance.

A torn screen can also be a problem. It could be a hassle or an issue. Additionally, it could prevent the doors from closing and opening properly, which can lead to energy loss. In some cases, the screen can be repaired however in other instances, the door must be replaced. If you're experiencing a tear in your screen, make sure you clean it thoroughly and make sure not to turn the door handles the wrong way when opening and closing.

Over time, hinges may become loose due to normal wear and tear or heavy usage. Regularly tightening the screws will help correct this issue and ensure your doors close tightly. It's an easy task you can tackle on your own. However, if you're not sure doing it yourself, you must seek out an expert.

It's also a good idea to clean your patio doors tracks and rollers. Simple vacuuming or brushing can take away dust and other debris that can hinder the smooth operation of your patio doors. You can also use a specific tool to clean away rust or dirt that has accumulated. Inspecting and tightening the screws on the hinges may aid in re-alignment but in some cases, it's best to replace them all together to ensure a secure and durable seal.





If your frames for your patio doors are sagging or warped, this can affect their alignment and performance. The warping or shifting may occur due to changes in the foundation of your home, but could be caused due to poor installation or due to frequent use. A professional can replace or repair your patio door frame and make sure it is properly aligned. This will allow it perform at its best.

Rollers

Sliding patio doors are great for bringing the outside in and providing plenty of light, however they do require some maintenance to ensure they are sliding smoothly. If you find that you need to really push the handle to get the door to move, or it simply doesn't move as smoothly as it did in the past it could be due to the rollers. As time passes, the lower track can fill with dirt, sand, and mud, making it difficult for the rollers to roll across. You can clean it and spray it with a lubricant such as 2Slick to see if that helps.

If the tracks have been cleaned, but the rollers are still not moving freely, then it's time to replace them. Replacement rollers are available for your door and track. You can purchase them at a variety of hardware stores however, you will require someone to help you remove and reinstall the rollers. Before you purchase replacements, take an accurate picture of the roller assembly that is mounted in the door frame, so the experts can identify the specific model and type you require. You can also look for specific characteristics like bumps, dimples, flared edges, and cut-outs that can narrow down replacement options.

Once the rollers are replaced after which you'll have to put your sliding door into its frame. This is a heavy door, so you may require assistance. Start by checking to make sure there aren't any screws securing the track in place on either side of the frame, and that they are loose enough to allow the bottom of the door to slide into the channel that is on top of the frame. If you have screen doors, take it from the opening and make sure it's free of track and rollers.

After installing the new rollers, gently insert the door in the frame. It should be lowered to ensure it is secured. If your rollers are adjustable, you can adjust them so that the door is able to be opened.