A-Provocative-Rant-About-Patio-Door-Lock-Repair-m

Patio Door Lock Repairs

Over time, patio doors undergo wear and tear which can cause lock malfunctions. However, there are easy and efficient methods that can restore your uPVC patio door's security.

These quick fixes will ensure your home is secure no matter if you adjust the lock or clean the mechanism.

Clean the Lock

Although patio doors are an excellent way to let the outside in and keep the elements out, they can also be a security risk in the event that your lock isn't operating as it should. With time, wear and tear, cold and hot weather, dirt, and debris can cause your patio door lock to become difficult to operate. With a little care, you can make sure that your lock for your patio door always functions properly.

To begin with, it's essential to clean the lock of your patio door and all the moving parts. This will help remove any grime or coatings that might be hindering the lock from working correctly. Begin by wiping the moving parts of your patio door's lock with a damp, clean cloth. then make use of a scouring pad, or a rough damp cloth to scrub the hard-to-reach parts of the door and frame that are covered in dirt. Then clean the lock with a dry cloth to get rid of any moisture. Let it air dry before you use it.

If your patio door is equipped with pin-tumbler locks, you can apply powdered Graphite to the key. You can also use a Teflon oil like WD-40 Multi-Use Product. This type of lubricant is able to be applied quickly and does not dissolve over time. If you're unable to find the right lubricant to use with your lock, use a pencil with more of a thicker tip. Put the pencil in the lock, and shake it to distribute the graphite.

The tracks for sliding patio doors also require regular maintenance to ensure that they're free of dirt, dust, and debris. These tracks are especially susceptible to snow and ice, which can cause them become stuck or slack, making it harder for your patio doors to open and close.

Clean the track rails and rollers of sliding patio doors by removing weather stripping that is damaged or dirty. Clean it, and then replace it. The same is true for patio door rollers, which can be cleaned and sprayed with a non-stick lubricant that will allow them to move freely.

Lubricate the moving parts

uPVC french doors, like sliding patio doors, operate with 3-4 or occasionally 5-point locking mechanisms which include the lock cylinder and handle operated by the key. They require maintenance and lubrication of the moving parts. This can be done using an oil that is thin but not WD40. It should be done at least once a year.

If sagging hinges aren't the cause, the door may be skewed and catch or rubbing against the strike plate hole within the frame. The solution is to take off the strike plate, and then use an abrasive chisel to increase the size of the mortise it rests in. This will allow the latch to fit into the hole, and prevent it from scratching against the frame.

Once the cylinder is cleared of the way, measure its width with the help of a book or piece wood that will fit in the gap between the adjustment screw and the lock. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the of the cylinder.

Check the width of the lock.

If your patio door latch isn't able to turn even after cleaning and oiling it could be because it's not aligned with the strike plate. Check to see if the door is properly balanced and whether the hinge screws are secure, but in many cases shifting the strike plate up or down can fix the issue.

patio doors repairs near me is when the strike of the lock is too small for the latch to engage. In this case, enlarge the opening using the hammer and chisel. Then, test the latch so that it does not rub against the door jamb frame or catch the frame.

Before buying a replacement lock, it is important to determine the mortise type of lock you currently have. This can be done by looking at the faceplate of the lock and noting if it is square or round. Examine each screw hole on the current lock and note the size. This information will assist you in finding an alternative lock that is the same size and is a perfect fit for the hole you have already.

In addition to identifying the current mortise lock you should also examine it for any bends or scratches that may require repairing. A badly damaged or bent latch is more likely to break than one that's been used much, so be sure to replace the lock with a brand new secure and safe version in the event you notice any signs of damage or wear.

Once you've identified the type of lock replacement you require Now it's time to start the actual repair. Remove the old handle and spindle out of your patio door, and then install the new one. Begin by installing the interior handle, aligning it with the spindle and then securing it with the two bolts or screws that secure it. Install the exterior handle after the interior handle. Once you have completed these steps Test the handles to ensure that they can be shut and open easily and that the latch works properly with the strikeplate.

Check the Strike of the Door.





The door latch and strike plate are the two components of the lock that work to ensure that the latch is secure the door. If these are misaligned and the latch doesn't latch the door shut properly. Fortunately, this issue is usually simple to fix.

Check the receiving holes of the strike plate to ensure they are clear of obstructions such as dirt or plastic plugs. Release the screws that hold the strike plate in place. This allows it to move vertically, but it will not be able to separate from the frame. Adjust the strike plate so that it aligns its receiving holes with the latch hooks of the door latch. Once the strike plate is adjusted tighten all screws and test if the door closes smoothly.

These plates are difficult to reach for homeowners with sliding patio doors. However they are vital to secure and unlock your door. The plates made of metal are located on the top and bottom jambs of the door, where they support its latch. Then, the door latch is placed on the strike plate to form the seal when it is closed. If the strike plate is damaged or rusted or not properly installed the latch may not properly lock the door.

One of the most common reasons for the patio door lock to become stuck or not close is a misalignment between the latch and strike plate. The easiest method to check for this is by performing the "lipstick test." Rub some lipstick on the outside of the deadbolt, and then apply masking tape over it. The lipstick will leave the mark when you shut the door. This will reveal exactly where the latch joins the strike plate. If the mark is too low or high you can easily adjust the strike plate.

If your patio door locks for sliding aren't working correctly they can help keep your home safe from burglars. You must resolve this issue as quickly as you can. Follow these simple steps to repair your patio door lock and restore it's functionality.