How-Much-Do-Kia-Picanto-Key-Fob-Replacement-Experts-Earn-k
How to Replace a Kia Sportage Replacement Key
For a variety of Kia models, the key contains a built-in keyless entry system. The key functions like an remote control and is exchangeable by a Kia dealer.
Key fobs can fail to function due to a number of reasons, such as batteries that are dead, worn-out buttons signal interference, or water damage. Here are some guidelines on how to get your Kia Sportage replacement key back to working.
How to replace a remote key or smartkey
The battery in your Kia's intelligent key will eventually need be replaced, regardless of whether it's a remote that starts with a push button or a normal metal key that doesn't contain transponder. This is particularly true if the car displays a message that the remote or smart key has low battery power.
This is a relatively easy procedure. To replace the key fob battery take the mechanical key from the slit on the back of the key fob. You then need to pry open the cover. Inside the key fob there will be a small screw that holds the battery in place. Remove the old battery by detaching the screw with a small screwdriver. Install the new battery and close the cut on the key fob.
Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock in the same way, you're set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to run errands around Brandon.
Note: Some key fobs (transponder chip or smart keys) may need to have their programming done. This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your key needs to be reprogrammed, then you must be aware of the number printed on the tag of the key code and then record it in a safe place.
How do you replace the battery?
If the Kia key fob doesn't respond to pressing the lock or unlock button, it's a sign that the battery is not fully charged. A low battery may also cause other issues such as the check engine light flashing on or delayed cranking of the engine. It is fairly easy to replace the key fob batteries by using only two tools.
Make sure you turn off your vehicle and close all doors prior to beginning. Find kia key fob , metal or plastic piece that is on the bottom of your key fob and move it until a metal key slides out. This key can be put into the door's driver handle to unlock your car.
To replace the key fob battery, remove the rear cover and use a pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and align the new one in a way that the "+" positive side is facing you, and the "-" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid damaging or breaking the metal contacts.
After the new battery has been installed after which you turn the key fob off and then turn it on in the ignition several times until the door locks cycle. Then you can test your Kia key fob to see if it is working properly again.
How to replace a smart keys
You can have a standard keyfob or a Smart Key, based on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade, unlike the standard key fob, which does not. Both types of key fobs have an internal battery that will eventually have to be replaced. This is a simple procedure which takes just two minutes.
Make sure to shut off your Kia and stand on a level and well-lit surface prior to you begin. Remember that the fob can contain small pieces that could be thrown off should you not be careful.
The small release button is located on the lower backside. This will be either a circular or rectangular slot. You can open the key fob by pressing the button.
Once you have the key fob opened and you are able to remove the old battery, and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After you've finished, your key fob should be able to lock or unlock and start your vehicle even if it's not running.
How do you replace the mechanical key?
The Kia keyfob is a wonderful convenience, allowing us to lock or unlock our car simply by pressing the button. As with all devices, the Kia key fob may have issues. Luckily, there are steps to take to resolve these issues and keep our key fobs in good condition for the long run.
One of the most common problems is a dead or dead battery. The battery could cause the device to stop working or operate intermittently. If this is what you are experiencing, replace the battery with a new one.
If this doesn't fix the issue you can try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not to damage internal components, or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a new one.
Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob and make sure it is working correctly. If the device not working, contact a locksmith or dealer to help resolve the problem. To avoid a lockout in the future make sure you get an emergency key that will work on all trunk and door cylinders.
