How-To-Explain-Fiat-Panda-Key-Fob-Replacement-To-A-FiveYearOld-i

Reasons Your Fiat 500 Key Fob Won't Work

A key fob with the fiat 500 number is a convenient way to open the doors and start the car. There are many reasons why the fob could stop working. It could be due to a dead battery, damage to the receiver module, water issues, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob doesn't function is due to a dead battery. Key fobs of today have a limited range of operation and must be within just a few inches of the vehicle to work. If you're far from your vehicle and you press the key fob button, the car won't respond and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) with a new battery of a reliable brand, like Panasonic Duracell or Energizer. You can find them at the local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The car will blink its parking lights, and the key fob will operate the lock and unlock buttons.





If the fob's key doesn't work after replacing the battery, it could have water damage that stops it from communicating with the receiver module in your vehicle. Water damage can occur in a variety of ways, such as simply splashing or submerging the key fob into saltwater at the beach. If you think your fob was exposed to water, put it in a rice bag to draw out the moisture. If this does not work, you'll have to get your fob reprogrammed either by an auto locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals to keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to become shorted and eventually cease to function. It's not a good thing to let the fob get wet however, don't give it up when you accidentally drop it in water, or fail to remove it from your pocket.

Remove the battery first. Clean the electronic chip using isopropyl or a similar product and dry it thoroughly before replacing the battery. Next check the fob to verify if it is working. If the fob doesn't work, it may have to be reset. This is usually handled by a professional or dealer auto locksmith.

If the key is a newer model and has never been programmed to your vehicle It will most likely need to be replaced completely. This is a straightforward process which can be accomplished by a professional automotive locksmith. The locksmith will have to cut the key to match the ignition of your vehicle. The locksmith will also have to reprogram your fob into the vehicle's system. This is a simple and cost-effective procedure that can be completed in the same day.

Receiver Module Issues

Your 500 key fob might not function because it's out of range. click through the up coming article has a range of 30 feet, so if you are too far from your vehicle it won't be able to respond to your commands. This can easily be resolved by moving it closer to your vehicle until it begins responding.

If you've replaced your coin battery (commonly known as a "button" or "watch") and the fob won't work it could be due to an internal circuit board problem. In the majority of cases, reprogramming your fob will fix the issue. You can find instructions on how to do this on the majority of automobiles by searching YouTube or consulting the owner's manual.

It's possible that you need to replace the metal retaining clips that hold the coin battery in place. If they loose tension, they could stop the coin battery from being seated properly and cause your remote to malfunction.

In rare cases the fob could be desync'd with your vehicle because of software or hardware issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances, they may need to install the software again in your body control module, as well.

Interference

Interference can also cause the key fob not to receive or transmit a signal. This can occur when the keyfob's location is in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob may not function due to a bad connection with the buttons, water damage or damage to the internal chips.

If the key fob has failed to work one day in the middle of the night or even after trying everything you can at home to resolve it e.g. replacing the battery, reprogramming it and using the spare key fob, it could have a faulty receiver module on your 500. The receiver module, which is located beneath the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands that are then read by the vehicle.

There's a quick and easy way to reset the 500's internal system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then, reconnect the battery. This will get rid of any remaining electricity and then restart the car's computer system, which could allow you to get your key fob working again. If the problem persists, you should consult an experienced technician. They will be able diagnose the root of any issues.