How-To-Save-Money-On-Fiat-500-Replacement-Key-Cost-b

Fiat 500 Replacement Key Fob

It might be time to replace the battery if your 500 remote key fob isn't working. If you do replace the battery and it doesn't work, then the problem is likely to be elsewhere.

United Locksmith specializes in the production of new keys for classic automobiles. We have the tools as well as the parts required for this service.

Dead Coin Battery

The most common reason your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The battery inside the key fob is likely to drain quickly in the event that you don't use it frequently enough. If your remote is beginning to show signs of loss of range or stopped working, then the battery may be dead.

Metal clips hold the battery in in the key fob. If the clips aren't tightly secured, they could result in contact issues that prevent the remote from receiving power. Use a flathead screwdriver break open the retaining clip and then remove the old battery. Choose a battery that is the same voltage, size and specification as the original.

Water exposure can cause the key fob to corrode or be damaged. Even a short bath in soapy, warm water can cause damage to the chip. Keep new key for fiat 500 .

Water Damage





Damage to your water supply could be the cause of your key fob not functioning properly. The rubber seals on key fobs keep them from being damaged by a slight drizzle or splash of water. However, it is important to keep the keys from the washing machine, the ocean and pool.

The key fob is equipped with an electronic chip in it that transmits a signal to your car's immobilizer system. This is the reason why your 500 can start or lock, but when the chip becomes wet, it's unable to longer work.

You can try cleaning the inside electronics of your keyfob using isopropyl alcohol, or an electronic cleaner to determine if they are still good. However, it is probably best to get a replacement from a dealer instead of trying to repair an item that has been submerged by salt water.

While a replacement fob could cost you a bit of money, it is a lot cheaper than having to pay for your Fiat 500 to be towed to the dealer and repaired! You can also do it yourself by following some simple steps. Just make sure you have the correct battery type before you attempt to open your key fob. There are step-by-step directions for any car keyfob on the internet.

Faulty Chip

The chip inside the key fob connects directly with the immobiliser in your car to ensure that the vehicle will only start when proper keys are inserted. If the chip is damaged or destroyed the car won't start regardless of what you do.

Damage to the water or a dead cell phone battery are among the most frequently cited reasons for a faulty chip. Whatever the reason, it's best to delegate this task to a locksmith, as they will be able to replace the chip fast and at a low cost.

If your key fob stops functioning after exposure to clean tap water or rain, remove the battery and wipe down the electronic component with a towel to ensure it's dry before putting it back in. If the key fob does not work, there is the possibility that it's a fried component and needs to be replaced.

Some people go to their dealer when they require an entirely new Fiat fob. However, this could be an expensive option. United Locksmith is the best place to go if you want your Fiat keyfob repaired at a reasonable cost. We have the equipment and know-how necessary to repair your Fiat key fob in a quick and professional way.

Faulty Receiver Module

Fiat key fobs transmit a signal to the vehicle which will unlock and close doors (and start the car if it has an automatic transmission) up to 50 feet. However, there are several things that can cause the fob to cease functioning. This could be due to a dead battery water damage, worn out buttons as well as a receiver issue. signal interference, or malfunctioning chips.

If the fob has been in a pocket that has experienced extreme trauma, such as being dropped on a hard floor or being washed in the washing machine the fob may not be able to communicate with the car's Body Control Module (BCM). The BCM is a security system that only accepts signals from genuine keys.

If this is the case, then you will require replacing your fob. A locksmith professional can handle all aspects of the replacement procedure, including programming a new one for the 500. In fact, they can offer you a clone key that functions the same way as your original fob (and costs less than the cost).