This-Weeks-Top-Stories-About-Patio-Doors-Repair-a

Patio Doors Repair - How to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet

Patio doors create a convenient and comfortable transition between your home and outdoor space. They can also save you money on cooling and heating bills by keeping air within your home.

But with time your sliding glass or French doors may lose their appeal. Fortunately, simple fixes can keep them looking and working as new.

Weatherstripping

It's 5 AM and you're letting your dog out for his morning routine when you stumble into a puddle of water right near your sliding patio doors. You look around and realize that the rain from last night has blown through the seals of your patio doors. Be prepared, this isn't going to be a five-minute project. With a bit of patience and a few tools, you can fix this and protect your dog from wet, cold feet as well.

The most important thing is to replace the weatherstripping, which closes the gap between the door and the jamb, keeping out moisture, pests, and drafts. It also helps keep your energy costs down. A quick inspection of your windows and doors will show you if the weatherstripping is in good condition or requires replacing.

There are many types of weatherstripping, such as felt, open-cell foam, vinyl, thermoplastic rubber and metals like bronze or copper. patio door repair has its advantages and drawbacks. Foam and open-cell foam are not expensive however, they are also known to be visible and not effective at blocking airflow. Vinyl is more expensive however, it's more durable and resistant to moisture. Rubber is an excellent choice for high-traffic areas because it won't wear out as quickly.

To install new weatherstripping remove the patio door from the frame by loosening the screws that adjust the rollers using the help of a screwdriver. Then using a flathead screwdriver unscrew the plugs that hold the weatherstripping in place at the bottom of the frame. Then, pull out the weatherstripping that was previously in place and take off any remaining adhesive from the bottom of the frame. Then, cut the new to the correct length, peel off the plastic strip at one end, and apply it using a putty-blade to the jamb.

Reinstall the door, and adjust the roller screws to ensure that it is properly seated in the track. Apply waterproof caulk to the area that the stationary panel passes through the sliding door and where the edge of the stationary panel is the frame. This is a less reliable seal than weatherstripping but should last for a while.

Handles and Locks

Locks and handles for patio doors are essential to the security of your home. Over time, they can be damaged or worn out and require replacement. Additionally, the spindle which connects the interior and exterior handles may also need to be replaced.

To replace the handle on a patio door, remove the previous one first by unscrewing any screws holding it in place. After the handle has been removed using a level, make sure the patio door is straight prior to installing the new handle. If the door isn't straight it could hinder the lock and cause issues later on.

Once you have the new handle installed, close and open it several times to make sure it is working properly. If you encounter any issues ask the manufacturer or a hardware expert for assistance. To avoid problems in the future it is recommended also to lubricate your lock mechanism with silicone-based lubricant.





The most commonly used patio door lock is the mortise latch. It is usually made of metal and sits in a pocket that has been cut into the frame of the door. They are usually used on sliding wood and aluminum doors. When replacing a mortise lock it's important to take a few measurements before purchasing a new lock. sliding patio door repair need include the mounting hole locations and the location of the keyway inside the lock.

Some patio door handles come with the ability to lock the handle. These handles have a rectangular key cylinder which fits into the handle's keyway. If you have this kind of patio door both the inside and exterior locks are combined into one. This type of patio door is often found on sliding aluminum doors.

If your patio door latch doesn't stay latched It could be due to the lock tongue isn't catching the jamb's hasp correctly. Another possibility is that the sliding door is not completely parallel to the jamb's side. Open the door one inch and then position it against the frame. This will reveal the gap between the jamb and the door. If there is a gap, adjust the rollers on the bottom left or right of the patio to make it perfectly parallel to the jamb.

Misalignment

Over time, the rollers and tracks of the door can lose their alignment. This can cause the door to sag or become difficult to move. This could also allow drafts and cold air enter your home, which can reduce energy efficiency. The issue of misalignment can be easily corrected and prevented. Applying a silicone-based oil to the rollers and tracks can help your doors move again. It is a good idea to do this periodically to ensure your doors are in peak operating condition.

A torn screen can also be an issue. It could be an inconvenience or even an issue. In addition, it can prevent the doors from opening and closing properly, leading to loss of energy. In some cases, the torn screen can be replaced, but in others it's necessary to replace the entire door. If you have a torn window screen, be sure you wash it thoroughly. Also, don't turn the handles of the door the wrong way.

Hinges can become looser over time due to frequent use or wear and tear. Regularly tightening screws can aid in fixing this issue and ensure your doors close tightly. It's a simple task that you can perform yourself. If you're not confident with the task, you should consult a professional.

It's also a good idea to clean your patio doors track and rollers. A simple brushing or vacuuming can remove dust and debris that could hinder the smooth operation of your patio doors. You can also use an instrument specifically designed to clear off rust or dirt that is hard to remove. The inspection and tightening of the screws on the hinges may aid in re-alignment however, sometimes it's necessary to replace them all together to ensure a solid, solid seal.

The performance and alignment of your patio doors can be affected when the frames are sagging or sagging. Shifting or warping can occur due to changes in the foundation of your home, but it could also be caused by poor installation or through frequent use. A professional can repair or replace your patio door frame, and ensure that it is properly aligned. This will allow it to perform its best.

patio doors repairs near me sliding patio doors are an excellent way to let the outdoors in and let in plenty of light, but they require some maintenance to ensure they are running smoothly. If you have to yank the handle hard to get the door to move or it doesn't move as smoothly as it used to, it could be the rollers. Over time, the lower track may become clogged with dirt, sand and mud that makes it difficult for the rollers to roll over. Clean it and spray it with a lubricant, such as 2Slick to see if that helps.

If the tracks have been cleaned but the rollers aren't able to move freely it's time to replace them. There is a variety of replacement rollers to suit your door and type of track you have. You can purchase them at most hardware stores, but will need someone to assist you in removing and reinstall the rollers. Before you purchase replacements, take a good picture of the roller assembly placed in the door frame, so the experts can identify the exact model and the type you require. You can also look for distinctive characteristics like bumps, dimples and flared edges, and cut-outs that could narrow your the options for replacement.

When the rollers are replaced then you'll need to install your sliding door in its frame. This is a very heavy door, and you might require help. Make sure there are screws that hold the track on either side of the frame. If they are check that they're loose enough to allow the bottom of door to drop into the channel above the frame. Remove the screen door from the opening. Make sure it's free of the track tracks, rollers and track.

After installing the new rollers, gently insert the door in the frame. Swing it down to ensure it is secured. If the rollers are adjustable you can adjust them to ensure that the door is able to be opened.