Three-Common-Reasons-Your-Patio-Door-Lock-Repair-Isnt-Performing-And-How-To-Fix-It-b

Patio Door Lock Repairs

Over time, patio doors go through wear and tear that can cause locks that fail. There are fortunately, a number of simple and efficient methods that can restore your uPVC patio door's security.

These simple fixes can make your home safer, whether you realign the lock or clean the mechanism.

Clean the Lock

Patio doors are fantastic for bringing the outdoors in and keeping the elements out. However they can pose a security threat in the event that the lock isn't working correctly. As time passes, wear and tear, extreme cold and hot weather dirt and debris can cause damage to your patio door's lock and cause it to become difficult to open. Fortunately, with a little maintenance you can make sure that the locks on your patio door always perform properly.

It is essential to first clean the patio door lock as well as all moving parts. This will help remove any dirt or coatings that might be hindering your lock from functioning properly. Start by wiping all the moving parts of your patio door lock using a wet cloth. Then apply a scouring pad or rough damp cloth to scrub the dirt-infested parts of the door and frame. Then clean the lock with a dry towel to get rid of any remaining moisture. Let it air dry before using it.

If your patio door has pin-tumbler locks, you can lubricate it by applying powdered Graphite to the key. You can also apply a Teflon lubricant like WD-40 Multi Use Product. This kind of lubricant can be applied with ease and doesn't dissolve over time. If you are unable to locate a suitable lubricant, you could try using a pencil that has a thick tip. Place the pencil in the lock and move it around a bit to spread the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio doors free from dust, dirt and debris. They are particularly susceptible to ice, snow, and other debris, which can cause them block or become stuck. This could make it difficult for your patio door to open and shut.

You can clean the track rails and rollers on sliding patio doors by removing damaged or dirty weather stripping. Clean it and replace it. The same can be done for rollers on patio doors, which can be cleaned and sprayed with non-stick lubricant in order to allow them to move freely.

Lubricate the Moving Parts

uPVC french doors, which are similar to sliding patio doors, operate with 3-4 or sometimes five-point locking mechanisms, which include the handle and lock cylinder controlled by the key. These doors also require maintenance, specifically lubrication on the moving parts. This can be done using an oil that is thin but not WD40. This should be done at least once per year.

If patio door repairs near me aren't causing the issue, it could be that the door isn't aligned. It may be rubbing or catching against the strike plate's opening in the frame. Take off the strike plate and use a sharp tool to increase the size of its mortise. This allows the latch to fit correctly in the hole, and also prevents getting caught or rubbing against the frame.

While the cylinder is out of the way, measure its width with an object or a piece of wood that fits into the adjustment screw gap above the lock. The outer dimension is measured from the outside of door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the width of the lock.





If your patio door latch isn't able to turn even after cleaning and lubricating, there's a possibility that it is out of alignment with the strike plate hole. Verify that the door is balanced and if the hinge screws are tight, but in many cases it is possible to move the strike plate upwards or downwards can fix the issue.

Oftentimes, the problem occurs when the strike of the lock is too small for the latch to engage. In this case, you'll need to enlarge the hole using the hammer or chisel and then test the latch to make sure that it contacts the strike plate in a smooth manner without rubbing against or catching on the door's frame jamb.

You must identify the kind of mortise lock you currently are using before you purchase the replacement. You can do this by taking a look at the faceplate of the lock and determining whether it is square or round. Then, take a look at the screw holes in the existing lock and note the dimensions of each one. This will enable you to locate a replacement lock that is exactly the same size and will fit in the hole you have already.

In addition to identifying the current mortise lock you should also examine it for any scratches or bends that may need repairing. A damaged or bent latch is more likely than one that's been used a lot to break. Replace the lock if it displays indications of damage.

After you've determined the type of lock replacement you need It's time to start the actual repair. The old spindle and handle should be removed from the doorway to the patio. Introduce the new handle. Begin by installing the interior handle. Align it with the spindle, and then secure it in place using the two screws or bolts. Once the handle in the interior is in, install the handle on the outside and screw it into place, too. After you've completed these steps, you can test the new handles to ensure they open and close easily and that the latch catches correctly when you strike the plate.

Check the Door's Strike

The door latch and strike plate are the two components of the lock that work together to ensure that the latch locks the door. A misaligned strike plate or door latches can cause the latch to not latch the door properly. This problem is usually very easy to repair.

First, inspect the strike plate's receiving holes to ensure they are clear of obstructions like dirt or plastic plugs. Loosen the keeper screws holding the strike plate in place. This will allow it to move vertically but not separate it from the frame. Adjust the strike plate so that it aligns its holes for receiving with the latch hooks of the door latch. After the strike plate has been adjusted, tighten the screws and then test the door to see whether it shuts easily with the new adjustment.

Door strike plates can be difficult to access for homeowners who have sliding patio doors, but they're essential for locking and unlocking your door. These plates are usually located on the top and bottom of the door jamb, where they serve as the door's latch. The door latch slides into the strike plate to create an airtight seal when closed. If the strike plate has been damaged or rusted, or if it is not properly installed the latch may not properly lock the door.

One of the most common reasons for an outdoor door lock to stick or not close is a misalignment between the latch and strike plate. The most effective way to test for this is by performing the "lipstick test." Rub some lipstick on the outside of the deadbolt, and then apply masking tape over it. The lipstick will leave an impression when you shut the door. This will reveal exactly where the latch meets the strike plate. If the mark is too low or high, you can easily alter the strike plate.

If your patio door locks for sliding aren't functioning properly they can help keep your home safe from burglars. You need to repair the issue as soon as you can. If you follow these steps, you can fix the lock on your patio door and regain its functionality within a short time.