What-Is-Everyone-Talking-About-Kia-Picanto-Key-Fob-Replacement-Right-Now-v

How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with a keyless entry system built in. The key is usually akin to an remote control, and can be changed by a new one purchased from an Kia dealer or locksmith.

Key fobs can stop working due to a variety of reasons, including batteries that are dead, worn-out buttons signals, signal interference or water damage. Here are some helpful tips to assist you in getting your Kia sportage replacement key working once more.

How to replace a remote key or smartkey

No matter if your Kia is equipped with an intelligent key, remote key push-to-start key, or a regular non-transponder metal key The battery inside these keys will eventually require replacement. This is particularly in the event that your car displays a message telling that the smart or remote key has a low battery.

Luckily, this is a relatively simple process. To replace the battery on the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, pry the cover open. Inside the key fob, there will be an incredibly small screw that holds the battery in its place. Using a small screwdriver, loosen the screw and pull out the old battery. Then, you can insert the new battery and close the slit on the key fob.





Test the key fob by pressing the lock and unlock buttons. You're in good shape if the doors lock and unlock as you expect. You can now use your Kia's hands-free lock/unlock feature whenever your fingers feel cold or you have to run some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a programming machine that is only available to the locksmith who works for the automotive dealer. Other keys (non transponder metal keys), do not need programming. If you need to reprogramme your key, you'll need to record the key code number on the tag for the key code.

How do you replace a dead battery?

If the Kia key fob does not respond to pressing the lock/unlock button, it is most likely that the battery is not fully charged. A low battery may also cause other issues, such as the check engine light coming on or a delay in cranking the engine. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires just a few basic tools.

Before beginning the process be sure that your vehicle is turned off and that all doors are closed. Locate the small metal or plastic piece on the bottom of your key fob and gently jiggle it until the metal key is released. The key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, remove the cover at the rear and use a plastic pry bar tool to release the latch that holds the black negative battery cable. Remove the old battery and then orient the replacement battery so that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or breaking the metal contacts.

After the new battery has been installed after which you turn the key fob off and then on in the ignition several times until the door locks cycle. You can then test your Kia key fob to see if it is working properly again.

How to replace the smart key

You can have a standard keyfob, or a Smart Key based on the model of Kia Sportage. sources tell me features an embedded mechanical key blade however, the standard key fob does not. Both kinds of key fobs come with a battery inside them which eventually needs to be replaced. This is a straightforward process that takes less than two minutes.

Before you start before you begin, ensure that you are on a level surface with good lighting and that your Kia is turned off. Keep in mind that the fob has tiny parts that could fall should you not be careful.

The first step is to locate the small release button on the lower backside of your fob. It will be a circular button or a rectangular slot. Once you press this, the mechanical key blade will come out and you will be able to open the key fob.

Once you have the key fob opened it is easy to take out the old battery and replace it. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. Once you're done, your key fob should permit you to lock, unlock, and start your vehicle even if it's not running.

How to replace the mechanical key?

The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car by simply pressing the button. Like any device that is used, the Kia key fob can have issues at times. There are methods to resolve these issues and keep our key fobs in good condition in the long run.

One of the most frequent problems is a dead or dead battery. This can cause your device to stop working or operate intermittently. If this happens you should replace the battery with a new one.

If this doesn't solve the problem, try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage any internal components, or scratch the plastic. Once the battery is removed, replace it with a brand new battery.

After the new battery has been put installed, close and unlock the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that will fit into the slot). Test the key fob to verify that it's working correctly. If the device isn't functioning, contact a dealer or locksmith to solve the issue. To avoid lockouts in the future, ensure you have an emergency key that can be able to work with all door and trunk cylinders.